Mircom TX3 Series Installation Manual download pdf (Page 28)

28 (122)

Telephone Access System Installation and Operation Manual

Version 3.2

Enclosure Installation

To install the Touch Screen Kiosk base plate

1. Find a suitable location for the Kiosk next to the building entrance and

above the building electrical and communications conduit.

2. Remove the door from the Kiosk.

3. Remove the 4 bolts from the reinforcement bracket, as shown in Figure 6

Figure 6 Reinforcement Bracket with bolts

4. Remove the 6 nuts on the reinforcement bracket, as show in Figure 7, and

then remove the bracket.

Bolts (x4)

Reinforcement Bracket

Nuts (x6)

Reinforcement Bracket

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 121 122

TX3 Series 1
Contents 3
List of Figures 5
List of Tables 7
Introduction 9
1.1 TX3 Systems 10
1.2 Features 11
1.3.1 Universal Series 12
1.3.3 Universal Slim-Line Kit 13
1.3.4 Continental Series 14
1.3.5 Kiosk Free Standing 15
1.6 About This Manual 16
1.7 Contact Us 17
1.7.3 Website 18
1.7.4 Email 18
1.7.5 Technical Support 18
Enclosure Installation 19
2.3 Installing the Heater 26
50.117 " 27
17.950 " 27
14.187 " 27
Bolts (x4) 28
Reinforcement Bracket 28
Nuts (x6) 28
Bolts (x8) 29
Base Plate 29
Kiosk Mounting Holes (x12) 29
TX3 System 33
3.1 TX3 System 34
3.2 Single Lobby Control Unit 35
ADC line and four NSL lines 36
3.3 Dual Lobby Control Units 37
3.6 Networking TX3 Panels 41
3.7 Lobby Control Unit Wiring 44
Lobby Control Unit Setup 45
4.1 Controller Board 46
4.1.1 Connectors 47
4.1.2 Potentiometer 47
4.1.3 Switches 47
4.1.4 Jumpers 47
4.2.1 Microphone Connection 48
4.2.2 Speaker Connection 48
4.2.3 Inputs 1 to 5 48
4.2.4 RS-485 50
4.2.5 Auxiliary Camera Supply 50
4.2.6 LED/Lamp Supply 50
Note: Use 18 AWG 51
4.3.1 Telephone Lines 1 to 5 52
4.3.2 JW8 52
4.3.4 AC Output Door Strike 53
4.3.5 DC Output Door Strike 53
4.4 Modem Board 54
4.5 MD-921 IP Module 55
4.6 MD-993 Module 56
4.7 Guard Phone Module 57
4.8 Guard Phone 57
4.9 Controller ID Setup 58
4.10 Configuration Using a PC 61
4.11 Updating Firmware 62
4.12 Beginning Configuration 62
65 (122) 65
Figure 36. NSL Relay Cabinet 66
67 (122) 67
TX3-NSL-8M Relay Control Unit 68
NSL Main Controller 68
NSL Backplane Board 68
1535 relays 69
5.3.1 Connectors 70
5.3.2 Switches 71
5.3.3 Jumpers 71
5.3.4 Telephone Line 71
TX3 Lobby Panel Main 72
Controller Board 72
73 (122) 73
75 (122) 75
Jumper Setting 76
Backplane Number 76
Selection 76
77 (122) 77
78 (122) 78
This connector mounts 79
Amphenol connection 79
80 (122) 80
81 (122) 81
82 (122) 82
83 (122) 83
84 (122) 84
85 (122) 85
5.4 Updating Firmware 86
Elevator Restriction Unit 87
Installation 88
89 (122) 89
90 (122) 90
91 (122) 91
6.3.2 Connectors 92
6.3.3 DIP Switches 92
6.3.4 Jumpers 92
6.3.5 USB 92
6.3.6 RS-485 93
6.4.1 Connectors 94
6.5.1 Relay Board Components 95
96 (122) 96
97 (122) 97
98 (122) 98
6.7 Updating Firmware 99
100 (122) 100
Version 3.2 100
7 Adding Controllers 101
7.1 Adding a Controller 102
Appendix 103
8.1 Specifications 104
8.1.6 Post Office Lock 105
8.1.7 Tamper Switch 105
8.1.8 Modem 105
Lobby Control Unit Kit 107
This chapter explains 111
9.1.1 Granting Access 112
9.1.2 Call Waiting Feature 112
9.1.3 Keyless Entry Codes 113
9.2.1 Granting Access 114
9.2.2 Keyless Entry Codes 114
Limited Warranty 115
International Warranty 115
Conditions to Void Warranty 115
Warranty Procedure 116
Disclaimer of Warranties 116
Out of Warranty Repairs 117
Special Notices 118
Type of Service 119
Telephone Company Procedures 119
Changes to Telephone Service 120
Ringer Equivalence Number 120
If Problems Arise 120
Product Identifier 121
Telephone Connection 121
Equipment Failure 121
Use With Alarm Auto Dialers 121
122 (122) 122

Comments to this Manuals

No comments

Mircom TX3 Series Installation Manual Page 28

Comments to this Manuals

Related products and manuals for Door intercom systems Mircom TX3 Series