Mircom QMT-5302 User Manual download pdf (Page 15)

NOT TO BE USED FOR INSTALLATION PURPOSES.

CAT. 5910

page 7 of 10

RAX-LCD Remote Shared Display

The RAX-LCD Remote Shared Display is a remote

annunciator that provides the same functions as the

main display on the fire alarm control panel, less

the 16 zone LEDs. In addition to operating as a

remote annunciator, it can also be used as a driver

module for standard LED annunciation or reduced

zone annunciation (different from the main panel

annunciation), graphic drivers programmed different from

the main annunciators, programmable switch modules

with a unique conguration and fan damper control also

with a unique conguration. Each time a different type

of annunciation conguration is needed an additional

RAX-LCD is required. The RAX-LCD occupies one

display position in the BB-1000 or BB-5000 enclosures.

Remote Annunciators

RAX-1048 Adder Remote LED Annunciator

The RAX-1048 Adder Remote LED Annunciator

provides an additional 48 points of LED annunciation.

The RAX-1048 is an expandible module that connects

to the RAM-1032. The RAX-1048 occupies one display

position in the BB-1000 or BB-5000 enclosures.

RAM-1032 Main Remote LED Annunciator

The RAM-1032 Main Remote LED Annunciator provides

common annunciator functions and 32 points of LED

annunciation. Each display point can be identied by the

slide-in label that slides in beside the LED. The RAM-

1032 is equipped with sealed membrane-like buttons

for Common Control functions. The RAM-1032 allows

for the control switches to be disabled on a per function

basis for areas that do not require certain common control

functions to be remotely located from the re alarm control

panel. The RAM-1032 can be programmed differently

than the main panel annunciator or a remote RAX-LCD.

All RAM-1032 remote annunciators on the system must

be programmed the same. The RAM-1032 occupies one

display position in the BB-1000 or BB-5000 enclosures.

MGD-32 Master Graphic Driver Module

The MGD-32 Master Graphic Driver Module provides

common control inputs for the common control switches

such as System Reset, Signal Silence, Auxiliary

Disconnect, Fire Drill, Lamp Test, Acknowledge and

General Alarm. Any or all of these switch inputs can

be used. There are supervised outputs for all of the

support LEDs and the common control switches. The

MGD-32 can also drive up to 32 supervised outputs.

These output points are capable of driving LEDs or

incandescent lamps. Mounts in a graphic annunciator

wallbox or in the BB-5000 enclosures. External power

supply required for incandescent lamps and lamp

test.

Graphic Annunciator Driver Modules

AGD-048 Adder Graphic Driver Module

The AGD-048 Adder Graphic Driver Module can be used

with either the MGD-32 or MGDS-16/16 Master Graphic

Driver modules, or if located remotely it must be connected

and mounted with the RAX-LCD Shared Display. The

AGD-048 will support an additional 48 supervised outputs.

As with the master modules, the AGD-048 will support

both LEDs and incandescent lamps. Mounts in a graphic

annunciator wallbox or in the BB-5000 enclosures.

NOTE:

The combined total of RAM-1032 and MGD-32 per system

is eight. All RA-1000 Series annunciators or Graphic driver

modules must have the zoned LED or graphic LED correlated

to the same combination of addressable devices or hardwired

zones . However, the zoned LED annunciator on the FX-

2000 main panel can be programmed differently from the

annunciators mounted remotely.

1 2 ... 10 11 12 13 14 15 16 17 18

Comments to this Manuals

No comments

Mircom QMT-5302 User Manual Page 15

Comments to this Manuals

Related products and manuals for Telephones Mircom QMT-5302