Mircom QMT-5302 Specifications Page 91
- Page / 152
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
FleX-Net
TM
Installation and Operation Manual
87
Integrated Fire Alarm Connection
The FX-2000ND/S Chassis consists of the Network Fire Alarm main board and chassis.
Battery Power
The power cable is used to provide power from the batteries to the FX-2000ND/S Fire Alarm main board and the
audio card cage motherboard. Power from the batteries is first directed to the Battery Disconnect Board, from this
board the power is connected to the main fire alarm board and the audio card cage. The red and black wires are
soldered on the audio card cage and the spade ends are connected to the red (+) and black (-) connectors on the
Battery Disconnect Board. The extra positive and negative wires (from the Y power cable) are connected to the
spades on the main fire alarm board and the spade connectors from the bottom of the Battery Disconnect Board are
hooked up to the batteries, red (+) and black (-). Refer to Figure 57.
Transformer Power
The orange, white, orange wires are soldered on the audio card cage motherboard. They are connected to the
terminal block located on the power supply cover (which covers the transformer) in the order left to right, orange-
white- orange. The orange-white-orange wires from the transformer are connected to the top terminals located on
the power supply cover in the same order (orange-white-orange). The yellow wire is connected to the 240V
terminal, the red wire from the transformer (120V) is connected to the 120V terminal on the fire alarm chassis, the
black wire (from the transformer) connects to the N terminal and the green wire (from the transformer) to the G
(Ground) terminal all located on the fire alarm chassis. If using 240V supply connect the yellow wire to the 240V
terminal, but do not connect the 120V red wire. The brown wires are connected to the bridge located on the fire
alarm chassis. Refer to Figure 57.
- LT-894 Rev. 3 1
- March 2013 1
- Table of Contents 3
- Introduction 5
- Overall Audio Features: 6
- Additional Features 7
- Document Conventions 7
- Node 2 - Floor Panel 9
- Node 3 - Floor Panel 9
- System Components 10
- Cutout to mount 11
- Network Controller Modules 12
- Adder Modules 12
- Display Modules 13
- Audio and Telephone Modules 14
- Booster Power Supply 15
- Enclosures 15
- Flush Trim Rings 16
- Remote Annunciators 16
- FA-UNIV-TRB 18
- BBX-1024DS BACKBOX AND DOOR 19
- BB-5008 Backbox 22
- DOX-5008M Metal Door 22
- Backbox with DOX-5008M Door 22
- Chassis Installation 23
- BB-5014 Backbox 25
- DOX-5014M Metal Door 25
- Backbox with DOX-5014M Door 25
- Module Mounting Locations 26
- FX-2000N Main Board 28
- Flexnet 30
- System Normal 30
- Module Settings 31
- DSPL-420 Main Display Module 32
- Alarm Module) 32
- MGC Network 33
- Fire Control System 33
- Main Display Module 34
- Fan Damper Operation 38
- OUTPUT MODULES 39
- MONITOR MODULES 39
- FIELD WI RING TERM INALS 40
- Basic Mode 41
- + 42
- UDACT-300A MAIN BOARD: 43
- LOOP (3) 46
- LOOP (4) 46
- JW2- normally shorted, a 47
- JW1- normally open 47
- Field Wiring 48
- TS2 Terminal Block is 49
- re alarm board 49
- FX-2000N 50
- FX-2000N 51
- 1 and 2 54
- STYLE 7 WIRING 56
- REDUNDANT WIRING 57
- Leg en d: 59
- SGM-1004A NAC BOARD 60
- RM-1008A Relay Module 61
- FPLR or FPLP MUST BE USED 62
- FROM PR-300 TO PROTECTORS 62
- Power Supply Connections 64
- Wiring Tables and Information 65
- Table 11: Analog Loop Wiring 66
- System Checkout 67
- Mircom FX-2000N 68
- Fire Alarm Control Panel 68
- Normal Condition 68
- January 6, 2013 68
- Common Indicators 69
- Common Controls 70
- Single Stage Operation 72
- Two Stage Operation 72
- Pre-Signal Operation 73
- Circuit Types 74
- Single stage codes 76
- Two-stage codes: 76
- Configuration 77
- Figure 48: Typical FleX-Net 78
- System with Audio Nodes 78
- Network Fire Alarm 80
- Fiber Optics Module 81
- Auxiliary Modules 81
- Programmable Modules 81
- FAN DAMPER 82
- BBX-FXMNS FRONT DOORS 84
- AND DEADFRONT CHASSIS 84
- BBX-FXMNS BACKBOX 84
- 16.5”16.5” 86
- 25” 25” 86
- 33.5” 33.5” 86
- QBB-5001(R) 88
- FX-2000ND FIRE ALARM 89
- MAIN BOARD 89
- FX-2000NDS FIRE ALARM 89
- Internal Wiring 90
- Battery Power 91
- Transformer Power 91
- 12 VDC BATTERY 92
- QPS-5000N 93
- EXPANSION MOTHERBOARD #1 94
- EXPANSION MOTHERBOARD #2 94
- EXPANSION MOTHERBOARD #3 94
- Audio Amplifier Wiring 96
- Amplifiers 99
- QAA-4CLA 100
- TERMINAL BLOCK 100
- QAA-4CLAS 101
- QAA-5160-70/25 102
- FleX-Net 103
- Backup Amplifier 104
- Displays & Controls 105
- AMP QAA-5203S-70/25 105
- Audio Configuration 106
- Lobby Enclosures 107
- + - + - + - S 108
- + - S + - L 108
- + - S+ - S 108
- + - S+ - L + - S 109
- + - S 109
- CLASS A WIRING 110
- Paging Modules 112
- Terminal Blocks 113
- + - + 114
- S - + 114
- S - + S - + L - + 114
- Paging Operation 115
- QAZT-5302/DS Pushbuttons 116
- ANC-5000 117
- TNC-5000 117
- Figure 79: 118
- + - S + - S 120
- - - + + - - + + 120
- - - + + 120
- TNC-5000 TNC-5000 121
- CLASS B WIRING 122
- CALL CONTROL 124
- ACTIVE 124
- DESELECT ALL 124
- TROUBLE INCOMING CALL 124
- QMT-5302N Connections 125
- Figure 88: 126
- Install Jumper for QZP 127
- Telephone Operation 128
- Appendix A: Specifications 129
- Compliance 130
- FX-2003-12N/ND/DS 133
- RAXN-LCD/RAXN-LCDG: 134
- Node Address 135
- Leave in "OFF" 136
- Factory Set 136
- ALCN - 792M 137
- Quad Loop Adder 137
- Paging/Telephone Zone Module 140
- BBX-2000 Enclosure 141
- Batteries 141
- MNS - ACU 143
- FX- LOC(R) 143
- FX-LOC(R) Active 146
- Limited Warranty 149
- Warranty Procedure 149
- Disclaimer of Warranties 149
- Out of Warranty Repairs 150
- © Mircom 2013 152
- Printed in Canada 152
Related products and manuals for Telephones Mircom QMT-5302
Telephones Mircom ADC Series User Manual
(2 pages)
(2 pages)
Telephones Mircom 9500 Series Specifications
(60 pages)
(60 pages)
Telephones Mircom 9500 Series Specifications
(116 pages)
(116 pages)
Telephones Mircom QMT-5302 User Manual
(12 pages)
(12 pages)
Telephones Mircom ADC Series User Manual
(24 pages)
(24 pages)
Telephones Mircom ADC Series User's Guide
(36 pages)
(36 pages)
Telephones Mircom QMT-5302 User Manual
(8 pages)
(8 pages)
Telephones Mircom ADC Series Specifications
(60 pages)
(60 pages)
Telephones Mircom QMT-5302 User Manual
(18 pages)
(18 pages)
Telephones Mircom QMT-5302 User Manual
(12 pages)
(12 pages)
Telephones Mircom ADC Series User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 2.197 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals