Mircom QMT-5302 Specifications Page 92
- Page / 152
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
QBB-5001/R Expansion Audio Cabinet Module Placement
88
QBB-5001/R Expansion Audio Cabinet Module Placement
The modules that mount into the QBB-5001/R expansion audio cabinet include the QPS-5000N Power Supply, the
QMB-5000B Motherboard, and the QBC-5000N Battery Charger. Module interconnects are shown in Figure 58.
There is no module installed into Slot #1 of the QMB-5000B Motherboard, as shown below.
Up to seven Amplifier Modules (Models QAA-5230-70/25, QAA-5230S-70/25, QAA-5415-70, QAA-5415-25 and/or
QAA-5160-70/25) may be installed into Slots #2 to #8 on the QMB-5000B motherboard. The total maximum wattage
per expansion audio cabinet is 360 Watts.
Figure 58: QBB-5001/R Expansion Audio Cabinet Module Placement
Components on the amplifiers should be facing left when inserted into motherboard. Make sure connections for the
power supply and battery charger are as shown above. Place all amplifier modules from left to right in slot positions
two to eight. Connect cable MD-525 from the QMB-5000N (inside the BBX-FXMNS or Integrated Fire/Audio
Cabinet) to the IN connector at the top left corner of the QMB-5000B Motherboard. Connect cable MD-525 from the
QMB-5000B Motherboard (connection marked OUT in the top left corner) to the next expansion audio cabinet QMB-
5000B Motherboard (connection marked IN) if another audio cabinet is used. Daisy chain all other expansion audio
motherboards used, up to a total of three.
12 VDC BATTERY
12 VDC BATTERY
INLINE FUSE 50A
- BATTERY +
XFORMER
Black
Black
120 or
240 VAC
Input
IN OUT
Red
Red
QBC-5000N
QMB-5000B
Motherboard
BATTERY
CHARGER
CONNECTORS FOR MULTIPLE
QMB-5000B MOTHERBOARDS
SLOT #1
CONNECTOR IS
NOT USED
SLOTS #2 - #8
CONNECTORS FOR
QAA- STYLE AMPLIFIERS
CONNECTOR FOR QBC-5000N
BATTERY CHARGER
QPS-5000N
POWER
SUPPLY
SECURE QPS-5000N POWER SUPPLY TO BACKBOX WITH LUGS AND NUTS PROVIDED
TS1
JW1
Orange-Yellow-Orange
(MUST BE IN CORRECT ORDER)
This represents the
Battery Disconnect
Relay located on the
left side of the box.
Battery
Disconnect
Relay
L N
- LT-894 Rev. 3 1
- March 2013 1
- Table of Contents 3
- Introduction 5
- Overall Audio Features: 6
- Additional Features 7
- Document Conventions 7
- Node 2 - Floor Panel 9
- Node 3 - Floor Panel 9
- System Components 10
- Cutout to mount 11
- Network Controller Modules 12
- Adder Modules 12
- Display Modules 13
- Audio and Telephone Modules 14
- Booster Power Supply 15
- Enclosures 15
- Flush Trim Rings 16
- Remote Annunciators 16
- FA-UNIV-TRB 18
- BBX-1024DS BACKBOX AND DOOR 19
- BB-5008 Backbox 22
- DOX-5008M Metal Door 22
- Backbox with DOX-5008M Door 22
- Chassis Installation 23
- BB-5014 Backbox 25
- DOX-5014M Metal Door 25
- Backbox with DOX-5014M Door 25
- Module Mounting Locations 26
- FX-2000N Main Board 28
- Flexnet 30
- System Normal 30
- Module Settings 31
- DSPL-420 Main Display Module 32
- Alarm Module) 32
- MGC Network 33
- Fire Control System 33
- Main Display Module 34
- Fan Damper Operation 38
- OUTPUT MODULES 39
- MONITOR MODULES 39
- FIELD WI RING TERM INALS 40
- Basic Mode 41
- + 42
- UDACT-300A MAIN BOARD: 43
- LOOP (3) 46
- LOOP (4) 46
- JW2- normally shorted, a 47
- JW1- normally open 47
- Field Wiring 48
- TS2 Terminal Block is 49
- re alarm board 49
- FX-2000N 50
- FX-2000N 51
- 1 and 2 54
- STYLE 7 WIRING 56
- REDUNDANT WIRING 57
- Leg en d: 59
- SGM-1004A NAC BOARD 60
- RM-1008A Relay Module 61
- FPLR or FPLP MUST BE USED 62
- FROM PR-300 TO PROTECTORS 62
- Power Supply Connections 64
- Wiring Tables and Information 65
- Table 11: Analog Loop Wiring 66
- System Checkout 67
- Mircom FX-2000N 68
- Fire Alarm Control Panel 68
- Normal Condition 68
- January 6, 2013 68
- Common Indicators 69
- Common Controls 70
- Single Stage Operation 72
- Two Stage Operation 72
- Pre-Signal Operation 73
- Circuit Types 74
- Single stage codes 76
- Two-stage codes: 76
- Configuration 77
- Figure 48: Typical FleX-Net 78
- System with Audio Nodes 78
- Network Fire Alarm 80
- Fiber Optics Module 81
- Auxiliary Modules 81
- Programmable Modules 81
- FAN DAMPER 82
- BBX-FXMNS FRONT DOORS 84
- AND DEADFRONT CHASSIS 84
- BBX-FXMNS BACKBOX 84
- 16.5”16.5” 86
- 25” 25” 86
- 33.5” 33.5” 86
- QBB-5001(R) 88
- FX-2000ND FIRE ALARM 89
- MAIN BOARD 89
- FX-2000NDS FIRE ALARM 89
- Internal Wiring 90
- Battery Power 91
- Transformer Power 91
- 12 VDC BATTERY 92
- QPS-5000N 93
- EXPANSION MOTHERBOARD #1 94
- EXPANSION MOTHERBOARD #2 94
- EXPANSION MOTHERBOARD #3 94
- Audio Amplifier Wiring 96
- Amplifiers 99
- QAA-4CLA 100
- TERMINAL BLOCK 100
- QAA-4CLAS 101
- QAA-5160-70/25 102
- FleX-Net 103
- Backup Amplifier 104
- Displays & Controls 105
- AMP QAA-5203S-70/25 105
- Audio Configuration 106
- Lobby Enclosures 107
- + - + - + - S 108
- + - S + - L 108
- + - S+ - S 108
- + - S+ - L + - S 109
- + - S 109
- CLASS A WIRING 110
- Paging Modules 112
- Terminal Blocks 113
- + - + 114
- S - + 114
- S - + S - + L - + 114
- Paging Operation 115
- QAZT-5302/DS Pushbuttons 116
- ANC-5000 117
- TNC-5000 117
- Figure 79: 118
- + - S + - S 120
- - - + + - - + + 120
- - - + + 120
- TNC-5000 TNC-5000 121
- CLASS B WIRING 122
- CALL CONTROL 124
- ACTIVE 124
- DESELECT ALL 124
- TROUBLE INCOMING CALL 124
- QMT-5302N Connections 125
- Figure 88: 126
- Install Jumper for QZP 127
- Telephone Operation 128
- Appendix A: Specifications 129
- Compliance 130
- FX-2003-12N/ND/DS 133
- RAXN-LCD/RAXN-LCDG: 134
- Node Address 135
- Leave in "OFF" 136
- Factory Set 136
- ALCN - 792M 137
- Quad Loop Adder 137
- Paging/Telephone Zone Module 140
- BBX-2000 Enclosure 141
- Batteries 141
- MNS - ACU 143
- FX- LOC(R) 143
- FX-LOC(R) Active 146
- Limited Warranty 149
- Warranty Procedure 149
- Disclaimer of Warranties 149
- Out of Warranty Repairs 150
- © Mircom 2013 152
- Printed in Canada 152
Related products and manuals for Telephones Mircom QMT-5302
Telephones Mircom ADC Series User Manual
(2 pages)
(2 pages)
Telephones Mircom 9500 Series Specifications
(60 pages)
(60 pages)
Telephones Mircom 9500 Series Specifications
(116 pages)
(116 pages)
Telephones Mircom QMT-5302 User Manual
(12 pages)
(12 pages)
Telephones Mircom ADC Series User Manual
(24 pages)
(24 pages)
Telephones Mircom ADC Series User's Guide
(36 pages)
(36 pages)
Telephones Mircom QMT-5302 User Manual
(8 pages)
(8 pages)
Telephones Mircom ADC Series Specifications
(60 pages)
(60 pages)
Telephones Mircom QMT-5302 User Manual
(18 pages)
(18 pages)
Telephones Mircom QMT-5302 User Manual
(12 pages)
(12 pages)
Telephones Mircom ADC Series User Manual
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 1.662 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals